
	ABOUT US \| CERTIFICATIONS \| CATALOG \| CONTACT US \| REQUEST QUOTE

Translate This Page

Catalog

Products

Master Flash

	Standard Flash
	Universal Flash
	Universal Retrofit
	Retrofit
	Square Vent Retrofit
	Residential Master Flash
	Multi Flash
	Res Led

Retrofit Master Flash®

Retrofit Master Flash is designed to seal existing pipes/vents where a standard pull over flashing cannot be assembled. The split design allows for an easy wrap around installation. Snap rivets and cable tie included.

Click to View

Installation EPDM

Installation Silicone

Rubber Specifications

SELECT and TRIM... Choose appropriate Retro Fit. If necessary trim opening to pipe diameter.
WRAP... Wrap Retro-Fit around pipe and install all snap rivets to seal flange.
FORM... Press Master Flash down, bending it to conform to roof profile or roof irregularities. A blunt tool will help press flashing into tight roof angles.
SEAL... Apply sealant between base and roof.
FASTEN... Use fasteners to complete sealing. For UPC installation, fastener spacing may not exceed 1-1/2" (38mm).
INSTALL CABLE TIE... Install supplied cable tie at uppermost part of Retro-Fit and apply sealant to any gaps.

Check diameter of your pipe or duct and select appropriate Retrofit Master Flash® to accommodate your application as indicated on the chart below. For extreme pitch or surface irregularity, select next larger size. Simply split the flashing at the designated area and close with the rivets and zip ties as instructed on the installation instructions.

RETROFIT MASTER FLASH®

WEATHER RESISTANCE

Designed to withstand the damaging effects of ultraviolet light and ozone.

MODIFICATIONS MADE SIMPLE

Easy to see pipe diameters make for painless on site customization.

MALLEABLE BASE

Designed to conform to most panel configurations and roof pitchesregardless of pipe location.

EASILY INSTALLED FASTENER SNAPS INCLUDED


	Designate Pipe Size	Compound	Part No.	Flashing Details
#1	1/2" - 4"	Black EPDM	RF101BP	A - Top Opening diameter 1/2" (12.7mm)
	(12.7mm - 101.6mm)	Grey EPDM	RF101GP	B - Pull to suit pipe size 1/2" - 4" (12.7-101.6mm)
		Red Silicone	RF102RS	C - Base Dimensions 8" - 3/16" (80.96mm)
#2	4" - 9-1/4"	Black EPDM	RF201BP	A - Top Opening diameter 4" (101.6mm)
	(101.6mm - 135mm)	Grey EPDM	RF201GP	B - Pull to suit pipe size 4" - 9-1/4" (101.6-234.95mm)
		Red Silicone	RF202RS	C - Base Dimensions 14-1/4" (361.95mm)
#3	9-1/4" -16-1/4"	Black EPDM	RF301BP	A - Top Opening diameter 9-1/4" (234.95mm)
	(235mm - 412.8mm)	Grey EPDM	RF301GP	B - Pull to suit pipe size 9-1/4" - 16-1/4" (234.95-412.75mm)
		Red Silicone	RF302RS	C - Base Dimensions 21-1/2" (546.1mm)

Flashing Detail

13821 Danielson St., Poway, California 92064 | 1-800-WASHER 5 (927-4375) | 1-858-513-4350 | Fax 1-858-513-4305

Master Flash®, Universal Master Flash®, Universal Retrofit Master Flash®, Retrofit Master Flash®, Residential Master Flash®,
Square Vent Retrofit Master Flash®, Master Seal® and Master Plug® are registered trademarks of Aztec Washer Company, Inc.
©2009 Aztec Washer Company, Inc. | Site Map | Privacy Statement